Battery holders
A battery holder is a plastic housing or connector to which batteries (AA, AAA, 9V block battery, etc.) are connected. Lab foods PCB power supplies USB power supplies Adapters Battery holders Batteries Power banks Batteries
40 resultsSort by
- 12mm Coin Cell Breakout w/ On-Off Switch Adafruit #1867 Simple but effective - this breakout board has a CR1220 coin cell battery holder soldered on, an on/off switch and 0.1" pitch breakout pins for easy connecting. Great for powering very low-current projects, or adding a battery backup circuit to a real-time-clock or similar.Delivered in 10 to 30 days€ 5,35 Incl. VAT
- 2-C Battery Holder Pololu #1157 This battery holder for two C cells features two 6″, 24-gauge leads that have approximately 5 mm of insulation stripped off of the ends.Delivered in 5 to 10 days€ 3,05 Incl. VAT
- 3-C Battery holder Pololu #1158 This battery holder is suitable for 3 C batteries, which are slightly wider than the well-known AA batteries. With the sturdy housing, a battery can be easily clicked off and on without having to glue the battery to the project.Delivered in 5 to 10 days€ 3,55 Incl. VAT
- 20mm Coin Cell Breakout w/On-Off Switch (CR2032) Adafruit #1871 Simple but effective - this sewable breakout board has a CR2032 coin cell battery holder soldered on, an on/off switch and 0.1" pitch breakout pins for easy connecting. Great for powering very low-current projects, or adding a battery backup circuit to a real-time-clock or similar.Delivered in 10 to 30 days€ 4,20 Incl. VAT
- Sewable CR2032 Battery Holder Adafruit #653 This battery holder is by far the easiest way to add a battery to a small wearable project. By coincidence, there are two small 1mm diameter holes in the metal connection tabs, just large enough for a #5 or smaller needle to pass through.Delivered in 10 to 30 days€ 2,65 Incl. VAT
- LilyPad Coin Cell Battery Holder - Switched - 20mm Sparkfun #DEV-13883 Sure, your flashing, chip-tune playing T-shirt is really cool at the party... but at some point you need to turn it off. And yes, you could just pull the battery, or maybe you've even sewn a LilyPad slide switch in-line. Wouldn't it be nice if there was just a switch *on *the battery?Delivered in 5 to 10 days€ 3,45 Incl. VAT
- CR123A Li-ion Battery Holder for micro: Maqueen DFRobot #FIT0611 This is a Li-ion Battery Holder specially designed for micro: bit educational robot Maqueen. It can be used to hold a CR123A 3.6V lithium rechargeable battery to provide more than 8 hours continuous power for Maqueen.Delivered in 5 to 10 days€ 10,15 Incl. VAT
- Kitronik Sewable Miniature Coin Cell Holder - CR1220 Kitronik #2718 This specially designed coin cell holder has large connection points for the conductive thread. These are clearly marked to show the battery polarity.Features:Specially designed coin cell holder with large connection points for conductive thread.Contents:1 x Sewable Miniature Coin Cell Holder.Delivered in 5 to 30 days€ 2,05 Incl. VAT
- Electro-Fashion Starter Pack, Standard Cell Holder Kitronik #2729 This pack is a great way to get started with E-Textiles.We have selected a number of products from our Electro-Fashion range, including three of our ultra-slim LEDs and two seperate power boards.Delivered in 5 to 30 days€ 11,65 Incl. VAT
- Electro-Fashion, Light Sensing Coin Cell Holder Kitronik #2721 This board allows LEDs to be turned on automatically when it is dark. On one side of the board is the coin cell holder, which takes a CR2032 coin cell as well as a small on-off slide switch. On the other side of the board is the light sensor.Delivered in 5 to 30 days€ 5,30 Incl. VAT
- Electro-Fashion, 60 Student Bulk Pack - Flat LEDs - 60 pcs Kitronik #2764 This fantastic new addition to the‘Electro-Fashion’ range from Kitronik has been specially designed so electronics can be used in textiles. They allow lighting effects to be added to textiles designs without any soldering.Delivered in 5 to 30 days€ 232,95 Incl. VAT
The 3 most popular Battery holders
A battery holder is a plastic housing or connector to which batteries (AA, AAA, 9V block battery, etc.) are connected. Battery holders may have a lid to hold and protect the batteries, or they may be sealed to prevent damage to circuits and components from battery leakage.
